Where to Put Jack Stands on Ford Fusion
There are various ways to support your Ford Fusion when changing a tire, but the most common and convenient method is to use jack stands. The question then becomes, where do you put them? The two best places to put jack stands on a Ford Fusion are on the frame rails just behind the front wheels or on the rear subframe just ahead of the rear wheels.
If you’re planning on doing some work on your Ford Fusion, you’ll need to know where to put the jack stands. The good news is, there are several different places you can use jack stands on a Ford Fusion. Here are a few of the most popular locations:
1. Front wheels – You’ll want to place the jack stands under the front wheels of your Ford Fusion when working on the engine or transmission.2. Rear Wheels – Jack stands can also be placed under the rear wheels of your car when performing work on the brakes or suspension.3. Frame Rails – Another great option for placing jack stands is under the frame rails.
This provides extra support and stability when working on any part of your car that’s located near the frame rails.4. Wheel Wells – If you need to raise your car higher off the ground, you can place jack stands in the wheel wells. Just be sure to use caution when doing this so that you don’t damage your car’s paint job.
5. Axle Shafts – For even more support, you can place jack stands under the axle shafts of your Ford Fusion.
how to: ford jacking points
Where Should Jack Stands Be Placed?
When working on a car, it is important to know where to place your jack stands. There are four main areas where you can place jack stands: the front wheels, the rear wheels, the frame, and the control arms.The front wheels are the most common area to place jack stands.
If you are going to be working on the engine or transmission, this is the best area to support the vehicle. The rear wheels are also a good option for supporting the car while you work on it. However, if you are going to be lifting one side of the car at a time, it is best to use jack stands in both the front and rear.
The frame is another area that can be used to support your vehicle while you work on it. This is especially helpful if you need to remove any body panels. Just make sure that the frame is solidly supported before attempting any repairs.
Finally, control arms can also be used as jack stand locations. This is helpful if you need to raise or lower one side of the vehicle independently from the other. Again, just make sure that both sides are properly supported before starting any work.
Where Do You Jack Up a 2015 Ford Fusion?
If you need to jack up your 2015 Ford Fusion, you’ll first want to find a level spot on which to park the car. Once you’ve found a suitable location, stop the car and set the emergency brake. Next, locate the jack points on the vehicle.
On the 2015 Ford Fusion, there are four jack points: two in front of the rear wheels and two behind them. Place the jack at one of these locations, then crank it until the wheel is off the ground. Be sure to use caution when jacking up your car, as it can be dangerous if done improperly.
How Do You Jack Up a 2014 Ford Fusion?
If you need to jack up your 2014 Ford Fusion, there are a few things you’ll need to do first. First, find a level spot on which to place the jack. Once you have the jack in position, insert the jack handle into the hole on the side of the jack.
Then, turn the handle clockwise until it stops. At this point, your car should be lifted slightly off the ground.To lower your car back down, simply turn the handle counterclockwise until it reaches its original position.
Where Does Jack Stand Go on Ford Focus?
Assuming you are referring to the jack stand point for lifting up your Ford Focus, it is located on the driver side near the front of the vehicle. More specifically, it is on the left side of the car where the door hinges are located. You will see a small notch in the metal near these hinge points- this is where you place your jack stand to support your car while you work on it.
Credit: www.reddit.com
2009 Ford Fusion Jack Points
The 2009 Ford Fusion has jack points located at the front and rear of the vehicle. The front jack points are located under the front fenders, just behind the wheel wells. The rear jack points are located on either side of the rear bumper, near the taillights.
When jacking up your Fusion, be sure to use a sturdy jack stand that can support the weight of your vehicle.
Conclusion
If you’re planning to do some work on your Ford Fusion, you’ll need to know where to put the jack stands. The best place to put them is on the frame rails. There are two of them, one on each side of the car.
They’re located just behind the front wheels.
